| ADD/OFF/INS | switch | — | Three-position switch. ADD appends new taps after the tapography end; INS inserts new taps within the existing tapography length; OFF disables tap input. In SEQ mode: OFF=forward sequencing, ADD=random slot, INS=random walk.168 |
| BANK | menu_setting | — | Selects the active bank (A, B, C, or D) for loading and saving tapographies. Each bank has 6 slots. Bank D is empty at factory.168 |
| Delete/Sync | button | — | Short press deletes the last entered tap (subject to Morph time). Long press toggles Sync mode (syncing tapography length to Ext Clock). Flashes white on each Gate Out trigger; red when Sync is active.168 |
| Dry/Wet | knob | — | Crossfades between the unaffected (dry) input signal and the sum of all taps (wet signal).168 |
| Feedback | knob | 0% – 120% | Injects the sum of all taps back into the delay input. Can build up to self-oscillation. A soft saturation is applied to the output and feedback path for analog-like clipping.168 |
| Level | knob | 0% – 300% | Sets the level of the signal going into the delay (wet path only; does not affect the dry path). 0% is silence into the delay, 300% is maximum amplification.168 |
| MODE | menu_setting | — | Selects between EDIT mode (create/modify tapographies) and SEQ mode (sequence between saved tapographies using the sensor or trigger input). Default is EDIT.168 |
| Modulation | knob | — | Controls amount and frequency of independent random sine-like LFOs on each tap time. Fully CCW: high frequency (~50Hz) but negligible amount. Fully CW: maximum amount (+/-0.5 sec) but LFOs are nearly stalled. Intermediate positions give useful wow-and-flutter modulation.168 |
| Morph | knob | 0s – 12s | Sets transition time (0 to ~12 seconds) when a tapography changes: adding/removing taps, clearing, enabling/disabling Repeat, or recalling a saved slot. Also controls morph speed in SEQ mode.168 |
| PAN | menu_setting | — | Sets stereo panning mode. ALT: alternates left/right per tap. RND: random panning from 100% left to 100% right. SUM/R: mono mode — Out 1 is sum of all taps, Out 2 is Repeat tap only.168 |
| RES/AMP/LPF | switch | — | Selects the velocity-to-parameter mapping for newly entered taps. RES: resonant band-pass filter, velocity controls center frequency. AMP: velocity controls volume. LPF: non-resonant low-pass filter, velocity controls roll-off frequency.168 |
| Repeat/Clear | button | — | Short press toggles Repeat (feeds last tap back at unity gain indefinitely, loop size fixed). Hold 0.5s clears all taps. Both subject to Morph time.168 |
| Tap Buttons 1 to 6 | button | — | Load and save tapographies within the current bank. Also used to navigate and change settings in the settings menu.168 |
| Tap sensor | button | — | Velocity-sensitive force-sensing resistor (FSR). Entering taps in EDIT mode adds taps at the tapped rhythm with velocity proportional to tap force. In SEQ mode, advances to the next tapography slot, with harder taps causing faster morphing.168 |
| Time | knob | 0.1 – 4 | Scales all tap times by a factor from about 0.1 to 4 (middle = 1). Compresses or expands the tapography in time; causes pitch shifting while moving. When Sync is engaged, selects clock multiplication/division (1/8 to 16).168 |
| VEL | menu_setting | — | Sets velocity sensitivity. For LPF and AMP taps: at MIN, amplitude/roll-off fully depends on velocity; at MAX, always maximum (no roll-off). For RES taps: sets Q from 1 to 20, MIN=less resonant, MAX=more resonant.168 |
| VEL NORM jumper | jumper | — | Sets the normalization of Velocity/Morph input when no cable is plugged in. HIGH: normalled to maximum velocity. TAP: normalled to the Tap/Next input amplitude, allowing trigger amplitude to set tap velocity.168 |