Eurorack Reference / modules /alm-busy-circuits/tazm-o audit site v0.1 — milestone 3
alm-busy-circuits/tazm-o

TAZM-O

ALM Busy Circuits

Analog triangle core through-zero FM oscillator with continuous morphing waveshape, voltage-controlled FM index, built-in output VCA, voltage-controlled octave transposition, dual sub-octave pulse outputs, hard sync, and LFO mode.317

Capabilities 3

Hard Synchard-sync
Any rising edge at the sync input hard-resets the oscillator core to the start of its cycle; can be used for timbral sweeping or LFO reset with a clock/trigger.317
LFO Modelfo-mode
Activated via latching push button; lowers frequency range to approx 0.1 Hz–30 Hz; bipolar LED indicates sine wave polarity.317
Through-Zero FMthrough-zero-fm
TZFM input with direct and voltage-controlled modulation index; works best when a related-frequency secondary oscillator is used as modulator.317

Jacks 12 — 7 in / 5 out

NameSignalVoltageDescription
Inputs (7)
FM Index CVcvCV input with attenuator controlling the FM Index VCA depth; allows dynamic TZFM modulation via LFO or envelope.317
Level CVcvCV input for the built-in output VCA level; functions as an attenuator when CV is inserted; usable for amplitude modulation effects.317
OCTcvOctave transpose CV input; transposes up 1 octave at approx 1V and up 2 octaves at approx 3V; ranges 3 octaves (0, +1, +2).317
Shape CVcvCV input with attenuator for waveshape/pulse-width modulation control.317
SynctriggerHard sync input; any rising edge resets the oscillator core to the start of its cycle. Usable for timbral effects or LFO reset with a clock/trigger.317
TZFMaudioThrough-zero FM input; audio-rate modulator signal is routed through an internal VCA controlled by the FM Index and its CV input.317
V/Octcv1V/octave pitch CV input with approximately 8 octave range.317
Outputs (5)
SawaudioDirect sawtooth output at base frequency.317
ShapeaudioMain morphing wave output passing through the built-in VCA; continuously morphs between sine/triangle, saw, pulse and square waveforms.317
SineaudioDirect sine (or triangle, selectable via rear slide switch) output at base frequency.317
Sub-1audioPulse output 1 octave below base frequency; fixed 50% duty cycle.317
Sub-2audioPulse output 2 octaves below base frequency; duty cycle selectable between 50% and 75% via rear slide switch.317

Parameters 10

NameTypeRangeBehavior
CoarseknobCoarse frequency tuning control for the oscillator.317
FineknobFine frequency tuning control for the oscillator.317
IndexknobControls the depth of through-zero FM by setting the level of the internal FM VCA. Can be modulated via the associated CV input with attenuator for dynamic FM.317
LFO Modebutton0.1Hz – 30HzLatching push button that activates LFO mode, lowering frequency to approx 0.1–30 Hz; bipolar LEDs above the switch indicate sine wave polarity.317
LevelknobControls output level via a linear VCA on the Shape output; acts as an attenuator when CV is patched in. Can be used for output level control or timbral amplitude modulation.317
OCT Transposemenu_setting0octave – 2octaveVoltage-controlled octave transposition: 0V = no transpose, approx 1V = +1 octave, approx 3V = +2 octaves.317
ShapeknobContinuously morphs the primary output waveform from sine/triangle through saw to pulse/square; pulse section scans from 10% to 90% duty cycle. Includes manual offset knob and CV input with attenuator.317
Sine/Triangle SwitchswitchRear slide switch selecting whether the bottom of the Shape morph (and the dedicated Sine output) produces a sine or triangle wave.317
Sub-2 Pulse Width SwitchswitchRear slide switch selecting Sub-2 output duty cycle between 50% and 75%.317
V/Octmenu_setting317

Firmware history 0 versions

No firmware history recorded.

References 2

  1. [317]
    ALM036 'TAZM-O' Operation Manualmanual
    verified 2026-05-13
  2. [318]
    ALM Busy Circuits TAZM-O product pageproduct_page
    verified 2026-05-13