Chronoblob2 is a digital delay module with four delay modes (Dual, Ping-Pong, Single, Cascade), clock sync, CV inputs for Time/Feedback/Dry/Wet, and an Infinite Loop function.313
Capabilities 2
Clock Syncclock-sync
SYNC input accepts a clock signal; delay time snaps to clock multiplications/divisions set by TIME knob. Module detects cable presence and stays in SYNC mode until cable is removed.313
Digital Delaydigital-delay
16-bit/48kHz digital delay with four modes (Dual, Ping-Pong, Single, Cascade), clock sync, CV modulation, and Infinite Loop.313
CV gate input for INFINITE LOOP. Activates when signal exceeds 0.7V.313
LEFT IN
audio
—
Main audio input. In pink modes (DUAL/PING-PONG), corresponds to the Left delay. In blue modes (SINGLE/CASCADE), is the main delay input. Also used as firmware update input.313
LEFT TIME CV
cv
—
CV input for delay time. Normalled to +5V when unpatched, allowing attenuverter to act as offset. In Dual/Ping-Pong modes, controls Left delay time independently.313
RIGHT IN
audio
—
In pink modes (DUAL/PING-PONG), corresponds to the Right delay; normalled to Left input when unpatched. In blue modes (SINGLE/CASCADE), acts as the feedback loop RETURN; normalled to SEND output when unpatched.313
RIGHT TIME CV
cv
—
CV input for Right delay time. Normalled to Left TIME CV when unpatched. Has no effect in SINGLE delay mode.313
SYNC
clock
—
Clock input. When patched, module enters SYNC mode and delay time snaps to clock multiplications/divisions. Module stays in SYNC mode until cable is removed, even if clock stops.313
Outputs (2)
LEFT OUT
audio
—
In pink modes, corresponds to Left delay output; becomes a 50/50 mix of Left and Right outputs when Right OUT is unpatched. In blue modes (SINGLE/CASCADE), is the main delay output.313
RIGHT OUT
audio
—
In pink modes (DUAL/PING-PONG), corresponds to the Right delay output; when unpatched, its signal is mixed into LEFT OUT. In blue modes (SINGLE/CASCADE), acts as the feedback loop SEND output.313
Parameters 10
Name
Type
Range
Behavior
DELAY MODE
button
—
Cycles through four delay modes: DUAL, PING-PONG (pink LEDs), SINGLE, CASCADE (blue LEDs). Hold for a few seconds to enter the settings editor.313
DRY/WET
knob
—
Controls the output mix between dry and wet signals using an equal-power curve. Fully left = dry only; fully right = wet only.313
DRY/WET CV att
knob
-100% – 100%
Bipolar attenuverter for the DRY/WET CV input, modulating the wet/dry mix. Center = no effect; CCW inverts.313
FEEDBACK
knob
≤125%
Sets the level of the feedback signal sent back to the delay input. Levels above 100% are indicated by a pink arc. A snap zone around the boundary snaps to exactly 100%. Maximum is 125%.313
FEEDBACK CV att
knob
-100% – 100%
Bipolar attenuverter for the FEEDBACK CV input. Center = no effect; CCW inverts the modulation polarity, CW attenuates it normally.313
INFINITE LOOP
button
—
Shuts off audio inputs and locks feedback at 100%, creating an infinite loop. By default acts as a toggle; can be changed to momentary in settings. In SYNC mode, waits for the next clock edge before activating.313
LEFT TIME CV att
knob
-100% – 100%
Bipolar attenuverter for the LEFT TIME CV input. Controls the left delay time in DUAL and PING-PONG modes; in CASCADE mode controls the outer (longer) delay; the single (combined) delay time in SINGLE mode. Center = no effect.313
MODULATION MODE
switch
—
Selects between TAPE mode (pitch-shift on time change, like a moving tape head) and FADE mode (quick crossfade to new delay time).313
RIGHT TIME CV att
knob
-100% – 100%
Bipolar attenuverter for the RIGHT TIME CV input. Controls the right delay time in DUAL and PING-PONG modes; in CASCADE mode controls the inner (shorter) delay. Has no effect in SINGLE mode (RIGHT TIME CV input is unused there).313
TIME
knob
5ms – 2730ms
Sets delay time. In SYNC mode, snaps to multiplications/divisions of the clock. Without SYNC, sweeps from 5ms to 2.73s. In Dual and Ping-Pong modes, controls both delays but each can also be voltage-controlled independently via the two TIME CV inputs.313