xaoc-devices/timiszoara
Timiszoara
Stereo voltage-controlled multi-effect signal processor based on the Spin Semiconductor FV-1 DSP chip, with two adjustable audio inputs, two outputs, stereo voltage-controlled wet/dry mixer, OLED screen, microSD card slot for loading effect programs, and up to three voltage-controlled parameters per effect.277
Capabilities 6
- CV Controlcv-control
- Up to three parameters per effect program are voltage controllable via dedicated CV inputs (10Vpp). The wet/dry mix and effect selection (scan/next) are also voltage controllable.277
- Delaydelay
- 277
- Filterfilter
- 277
- Multi-Effects Processormulti-effects
- 176 factory programs organized in banks of 8, covering delays, reverbs, modulations, filters, pitch shifters, distortions, glitching, and stuttering. Based on the Spin Semiconductor FV-1 DSP chip with 24-bit converters.277
- Pitch Shifterpitch-shift
- 277
- Reverbreverb
- 277
Jacks 10 — 8 in / 2 out
| Name | Signal | Voltage | Description |
|---|---|---|---|
| Inputs (8) | |||
| CV 1 | cv | -5V to 5V | CV input for parameter 1 of the current effect program. Accepts 10Vpp. With slider at middle, ±5V sweeps entire range; with slider at minimum, 0–10V sweeps entire range.277 |
| CV 2 | cv | -5V to 5V | 277 |
| CV 3 | cv | -5V to 5V | 277 |
| IN L | audio | — | Left audio input. Normalled to the right input before the input attenuators. Both input attenuators must be adjusted even with a single mono signal.277 |
| IN R | audio | — | Right audio input. Normalled to the left input before the input attenuators.277 |
| MIX CV | cv | — | CV input for the analog wet/dry mixer. The same 10Vpp range applies as for the param CV inputs.277 |
| NEXT | trigger | — | Trigger input that advances to the next program in the current bank and loads it automatically. The list is arranged in a loop, wrapping from position 8 back to 1.277 |
| SCAN | cv | -5V to 8V | CV input for scanning programs. Each 1V change shifts selection by one program position forward or backward. Removing the cable returns to the state from before CV control was applied.277 |
| Outputs (2) | |||
| OUT L | audio | — | 277 |
| OUT R | audio | — | 277 |
Parameters 5
| Name | Type | Range | Behavior |
|---|---|---|---|
| MIX | fader | — | Controls the analog wet/dry crossfader that blends the original (dry) signal with the processed (wet) output. Voltage-controlled via the MIX CV jack.277 |
| PARAM 1 | fader | — | Controls parameter 1 of the current effect program. Parameter name is displayed on the OLED screen. Works in conjunction with CV 1 jack; CV input accepts 10Vpp, with slider at middle position ±5V sweeps the entire range.277 |
| PARAM 2 | fader | — | 277 |
| PARAM 3 | fader | — | 277 |
| Program | menu_setting | — | Selects the active effect program from the currently loaded bank of up to 8 programs using the rotary encoder. Can also be advanced via the NEXT trigger input or scanned via the SCAN CV input.277 |
Firmware history 0 versions
No firmware history recorded.
References 3
-
[277]
Xaoc Timiszoara Operator's Manual (voltage controlled DSP effector)manual● verified 2026-05-06
-
[278]
Xaoc Timiszoara Program Chart (algorithm reference)manual● verified 2026-05-06
-
[279]
Xaoc Devices Timiszoara product pageproduct_page⚠ verified 2026-05-06 · manufacturer changed since last verified